Mainstream of bearing types

For bearing types,linear plain bearings and mobile crane bearing is the mainstream, but most of the use of self-aligning roller bearings in the non linear favorable. Non linear spindle generally need to consider the plus or minus 0.5 degrees.
As B type automatic self-aligning roller bearing  is designed by the use of the middle block side guide roller , it is no skew of the maximum load wide in the minimum load to load region , which can run in a stable torque and low fever cases.
In addition,vibration of blade and gear box vibration increasing of the rotor thin wall bearings, there is danger of corrosion and friction .Therefore, optimal bearing selection and clearance and mating and selection of suitable oil is very important.

Tapered roller bearings for use in the environment under which

tapered roller Full complement cylindrical roller bearing are precision components, its use should also be carefully carried out. No matter how high-performance bearings, if used improperly, it will not get the expected performance. Use Notes on tapered roller bearings are as follows.
First, keep tapered roller bearings and their surroundings clean
Even tiny invisible dust into the tapered roller bearings, will increase wear, vibration and noise of the bearing. tapered roller bearings and its peripheral accessories should be kept clean, especially the dust and dirt, tools and working environment must be kept clean.
Second, when using the installation to be carefully
Does not allow a strong punch, not allowed to use a hammer, a direct hit  tapered roller bearings are not allowed to pass through the rolling pressure.
Third, the use of appropriate and accurate installation tool
Try using a dedicated tool, try to avoid using fabric and staple fiber stuff like that.
Fourth,  tapered roller bearings to prevent corrosion
Direct hand pick  tapered roller miniature linear bearings  to fully wash hands sweat, and coated with high quality mineral oil and then operate in the rainy season and summer with particular attention to rust. However, in some special operating conditions, the bearing can be obtained in a longer life of traditional computing, especially under light load conditions. These particular operating conditions that, when the rolling surface (track and rolling elements) are effectively separated and limit pollutants may cause surface damage of a lubricant film. In fact, under ideal conditions, the so-called permanent tapered roller bearing life is possible.
Use the site and conditions of use and environmental conditions to select size, precision, with appropriate tapered roller bearings based on the bearing life and viability of the premise.
1, using the site: tapered roller bearings for joint load to bear radial load mainly radial and axial, usually paired with two sets of crossed roller bearings  primarily for automotive front and rear hub, active gear, differential , a reducer and other transmission parts.
2, the permissible speed: install properly oiled environment, allowing for tapered roller bearings 0.3-0.5 times the speed limit. Under normal circumstances, to 0.2 times the speed limit is the most appropriate.
3, allowing the tilt angle: Tapered roller bearings are generally not allowed to tilt axis relative to shell hole, if inclined, to a maximum of 2 '.
4, allowing the temperature: in under normal load, and lubricant high temperature performance, and under conditions sufficient lubrication, tapered roller bearings are generally allowed to work at -30 ℃ -150 ℃ ambient temperature.

Wheel bearing installation, use common sense

Car wheel bearings are used in pairs over most single row tapered roller or ball bearings . With the development of technology, the car has been widely used car wheel units. Growing scope and use of the hub bearing unit, has now developed to the third generation: the first generation is a double row angular contact bearing components. The second generation of the outer raceway has a flange for fixing the bearing, the turntable bearing sleeve may simply be fixed with a nut on the axle.So that the vehicle maintenance becomes easy. The third generation wheel hub bearing units are used bearing units and anti-lock brake system fitted. Wheel hub unit is designed to have the inner flange and outer flange, the inner flange is bolted to the drive shaft, the entire bearing outer flange fit together.Worn or damaged wheel bearing or hub units will make your vehicle is involved in a high anachronistic and costly failure in traveling the road, or even cause damage to your safety. In the wheel bearings use and installation Please note the following:
1, in order to ensure maximum safety and can be *, regardless of the age of the vehicle is recommended that you should always check how long the wheel bearings - note bearing for wear early warning signals: includes any friction or noise when rotating wheel suspension combination abnormal deceleration when cornering.Rear-wheel drive vehicle is recommended for the vehicle to 38,000 km is to deal with the front wheel hub double row ball slewing bearing lubrication. When replacing the brake system, check the bearings and replace seals.
2. If you hear noise emitted wheel bearing parts, first of all, it is important to find the location of the noise occurs. There are many moving parts may produce noise, but also may be some non-rotating member and the rotating member contact occurs. If the confirmation is bearing noise, the bearing may be damaged and need replacing.
3, because the front wheel hub bearing failure leads to both sides working conditions are similar, so even if only one bearing bad, it is recommended to replace in pairs.
4, wheel bearing more sensitive, in any case need to adopt the right approach and the right tools. In storage and during installation, the thin wall bearings

 parts can not be damaged. Some bearings require greater pressure pushed, so they need special tools. Be sure to reference vehicle manufacturers instructions.
5, when installing the bearings should be clean and tidy environment, small particles from entering the bearing will shorten bearing life. When replacing the bearings to maintain a clean environment is very important. Do not allow the bearing with a hammer percussion, note bearing not fall to the ground (or similar misconduct). Before installing the shaft and the bearing housing should also check the condition of, even minor would lead to undesirable wear of mating, thereby causing early failure of the bearings.